Anker SOLIX C1000 Gen 2 Review: 49-Minute Charging, 2,000 W Output and Verdict

Quick Verdict: Top Picks

Picks are based on the manufacturer specs and the math in this guide. Prices change often, so check the current price on Amazon.

Our Anker SOLIX C1000 Gen 2 review gives it 7.3 out of 10. On paper it’s built around speed: a full wall recharge in 49 minutes at 1,600 W, 2,000 W of continuous AC output and a 10 ms UPS, all in a 24.9 lb body. It loses points for its 600 W solar input, a warranty term that Anker’s product page doesn’t state, and no expansion.

This is a spec-sheet review, not a bench test. Every number comes from the Specs tab, official comparison table and FAQ on Anker SOLIX’s U.S. product page, read on November 19, 2026. Every runtime uses the open formula from our runtime calculator, and the score follows the same 10-point rubric we apply to every station.

Our Score: 7.3 out of 10

The table breaks this Anker SOLIX C1000 Gen 2 review score into its ten rubric lines. Each line rests on a published spec, so you can see where the Gen 2 leads the 1 kWh stations we’ve compared and where its design choices cost it points.

Rubric line (max points)ScoreSpec behind it
Capacity (1)0.51,024 Wh, the 1 kWh class
AC output (1)12,000 W continuous, 3,000 W peak
Wall charging (1)1100% in 49 min at 1,600 W UltraFast, per Anker
Solar input (1)0.5600 W, 11–60 V
Outage switchover (1)1UPS, 10 ms
Portability (1)1About 41 Wh per lb (24.9 lb)
Chemistry and cycles (1)0.7580% after 4,000 cycles; chemistry not stated on the U.S. page
Warranty (1)0.5Term not stated on the U.S. product page
Value (1.5)1Official-store price per Wh (price and date in the text)
Expansion (0.5)0Not expandable, per Anker’s FAQ
Total7.25 → 7.3

The Gen 2 earns full marks on output, charging speed, switchover and portability, which are the lines that matter most for frequent short outages and travel. The warranty line is half-scored only because Anker’s product page says “Hassle-Free Warranty” without a term; if Anker publishes one, we’ll update the score.

Anker SOLIX C1000 Gen 2 Specs at 120 V

These are the specs from Anker SOLIX’s U.S. Specs tab that matter for home backup and travel. The peak figure is in parentheses next to continuous AC output, and the charging time is Anker’s published figure with UltraFast mode switched on in the app.

Models at a glance

Specs from each model's U.S. manual or official datasheet. Full comparison in the table below. As an Amazon Associate we earn from qualifying purchases.

ModelCapacityAC output (120 V)Outage switchoverAC charging inputSolar inputWeightPrice
Anker SOLIX C1000 Gen 21,024 Wh2,000 W (3,000 W peak)UPS, 10 ms1,600 W UltraFast (100% in 49 min)600 W, 11–60 V24.9 lbCheck Price for Anker SOLIX C1000 Gen 2 (opens Amazon in a new tab)

Source: Anker SOLIX C1000 Gen 2 U.S. Specs tab, comparison table and FAQ (model A17631A1), read November 19, 2026. The default AC input is 1,200 W; UltraFast at 1,600 W is enabled in the Anker app. AC bypass is rated at 1,800 W.

The Gen 2 has ten ports in total, including its 120 V AC outlets, a USB-C port rated at 140 W (with a 20 V/5 A profile), a second USB-C and a USB-A port that share 20 W, and a 12 V/10 A car socket rated at 120 W. Solar and DC charging come in through an XT60i port.

At 15.12 × 8.19 × 9.61 inches and 24.9 lb, it’s one of the most compact 1 kWh stations we’ve compared, about 3.5 lb lighter than the original C1000. That’s light enough for camping and car trips, not just a closet battery for outages.

Runtime at 120 V

This runtime table is the practical core of our Anker SOLIX C1000 Gen 2 review. We treat 85% of rated capacity as usable, run AC loads through an 85%-efficient inverter and add an assumed 10 W of idle draw, since Anker publishes no idle figure for the Gen 2.

Load (example)Runtime
Wi-Fi router and modem, 20 W (AC)26.0 h
CPAP with humidifier and heated tube, 34 W (AC)17.4 h (about 2 nights of 8 hours)
Refrigerator, 600 kWh/yr label, about 68.5 W average (AC)9.6 h
TV and streaming box, 100 W (AC)6.8 h
Starlink Mini at 40 W on 140 W USB-C (DC)19.6 h
Microwave drawing 1,500 W from the outlet (AC)About 29 min

AC formula: hours = rated Wh × 0.85 ÷ (load W ÷ 0.85 + 10 W). DC formula: hours = rated Wh × 0.85 ÷ (load W ÷ 0.90), where 90% converter efficiency is our assumption. The CPAP figure is ResMed’s published average for an AirSense 10 with humidifier and heated tube (doc. 1018673/1). For CPAP use, check your device manual and talk to your doctor or equipment supplier first.

The USB-C row shows why the 140 W port matters: running a Starlink Mini on DC skips the inverter and gains about 28% over AC under our formulas. Our Starlink power station guide has the full math. For a refrigerator, the 2,000 W rating easily covers the roughly 1,200 W Honda lists for an Energy Star model’s start.

Charging: 49 Minutes with Conditions

The headline feature of any Anker SOLIX C1000 Gen 2 review is the 49-minute recharge, and it comes with conditions. Anker’s FAQ says you enable UltraFast Charging in the app with the AC cable connected, and that charging slows significantly when the battery cells are below 68°F (20°C). The default AC input without UltraFast is 1,200 W.

Anker also recommends using UltraFast only when necessary to prolong battery life, so think of 49 minutes as an emergency mode for rolling outages or a short generator run. At its 1,200 W default, Anker doesn’t publish a full-charge time, and several 1 kWh stations we’ve compared accept more AC input, so UltraFast is what sets it apart in this Anker SOLIX C1000 Gen 2 review.

Solar input tops out at 600 W from 11 to 60 V, with current limits of 8.2 A from 11 to 28 V and 14.5 A from 29 to 60 V. Anker lists a 1.8-hour solar recharge at 600 W; check your panel string in our Voc & MPPT compatibility checker before wiring panels in series.

Switchover, Battery and Expansion

The 10 ms UPS is tied for the fastest figure among the 1 kWh stations we’ve compared. Anker positions it for CPAP machines and laptops (for CPAP use, check with your doctor or equipment supplier first), and it gives a desktop PC or NAS more margin than a 20 ms or 30 ms switchover would. If a device must not reboot, check its power-supply hold-up time as well.

Anker rates the battery to keep at least 80% of its capacity after 4,000 cycles, matching the best cycle rating among the 1 kWh stations we’ve compared, though Anker’s U.S. page doesn’t name the cell chemistry. The Gen 2 also supports Time-of-Use mode in the app, which charges from the grid when electricity is cheap and discharges during peak-rate hours.

There’s no expansion. Anker’s FAQ says the Gen 2 leaves out an expansion feature to reduce weight and size, and recommends the original C1000 for buyers who need expandable capacity. Our Anker C1000 vs C1000 Gen 2 comparison covers that choice.

Value and Price

For the value line of this Anker SOLIX C1000 Gen 2 review, we scored the list price. Anker SOLIX’s U.S. store listed the Gen 2 at $699.99 on November 19, 2026, about $0.68 per rated watt-hour, with a Black Friday option showing $529.99 (about $0.52) the same day. At that sale price it would earn the full value score.

Even at list price, the Gen 2’s case is speed and portability rather than raw capacity. The BLUETTI AC180 offered more watt-hours for less money that day, but it charges slower, switches over in 20 ms or less and weighs about 10 lb more.

Anker SOLIX C1000 Gen 2 Review Verdict: Who Should Buy It and Who Should Skip It

This Anker SOLIX C1000 Gen 2 review lands on a clear profile: it’s the 1 kWh station for people who recharge often and move their station around. Buyers who want maximum capacity for the money, or room to grow, have better options.

Who should buy it: households facing frequent short or rolling outages, generator owners who want a fast top-up, Starlink Mini and laptop users who want a 140 W USB-C port, and campers who value a 24.9 lb station with a 10 ms UPS.

Who should skip it: anyone who expects to need more than about 1 kWh later, solar-first users who want 1,000 W of input, and buyers who want the lowest price per watt-hour at list price.

Alternatives to Consider

If you want more solar input and an expansion path with the same 10 ms switchover, read our EcoFlow DELTA 3 Plus review, which scores 8.8/10. If price per watt-hour comes first, our BLUETTI AC180 review covers a 1,152 Wh station at a lower price per watt-hour.

For a full day on a refrigerator, step up to the 2 kWh class in our 2000Wh power station comparison. Check current prices in the model card above.

Frequently Asked Questions

Is the Anker SOLIX C1000 Gen 2 worth it?

Yes, if speed and weight matter: a 49-minute recharge at 1,600 W, 2,000 W of output and a 10 ms UPS in a 24.9 lb body. It scores 7.3/10 on our spec rubric, held back by 600 W solar input, no expansion and an unstated warranty term.

How do you get the 49-minute charge on the C1000 Gen 2?

Turn on UltraFast Charging in the Anker app with the AC cable connected. Anker says it charges much more slowly when the cells are below 68°F (20°C), and recommends using UltraFast only when necessary.

How long will the C1000 Gen 2 run a refrigerator?

About 9.6 hours for a refrigerator with a 600 kWh/year EnergyGuide label, under our assumptions of 85% usable capacity, an 85%-efficient inverter and 10 W of idle draw. Its 2,000 W rating covers a typical compressor start.

Is the Anker SOLIX C1000 Gen 2 expandable?

No. Anker’s FAQ says the Gen 2 doesn’t include an expansion feature, to reduce weight and size, and recommends the original C1000 for buyers who need expandable capacity.

Can the C1000 Gen 2 power a Starlink Mini?

Yes. Its USB-C 2 port is rated at 140 W with a 20 V/5 A profile, which meets the Mini’s 100 W USB Power Delivery requirement. At 40 W, that’s about 19.6 hours under our DC assumptions.